Cisco Meraki MR44

• 2.4 GHz 802.11b/g/n/ax client access radio 
• 5 GHz 802.11a/n/ac/ax client access radio 
• 2.4 GHz & 5 GHz dual-band WIDS/WIPS, spectrum analysis, & location analytics radio
• 2.4 GHz Bluetooth Low Energy (BLE) radio with Beacon and BLE scanning support
• Concurrent operation of all four radios
• Supported frequency bands (country-specific restrictions apply):
  • 2.401 – 2.484 GHz 
  • 5.150 – 5.250 GHz (UNII-1) 
  • 5.250-5.350 GHZ (UNII-2A)
  • 5.490 – 5.730 GHz (UNII-2C)
  • 5.735 -5.825 GHz (UNII-3) 

• Internal Antenna (5.1dBi max gain at 2.4 GHz, 5.9dBi max gain at 5 GHz) 

• DL-OFDMA**, UL-OFDMA**, TWT support**, BSS Coloring** 
• 2.4GHz: 2 x 2 multiple input, multiple output (MIMO) with two spatial streams 
• 5GHz: 4 x 4 multiple input, multiple output (MIMO) with four spatial streams 
• SU-MIMO, UL MU-MIMO** and DL MU-MIMO support 
• Maximal ratio combining (MRC) & beamforming 
• 20 and 40 MHz* channels (802.11n); 20, 40*, and 80 MHz channels (802.11ac Wave 2); 20, 40* and 80 MHz channels (802.11ax) 

Note: *40MHz channels are supported only in the 5GHz band.

• Up to 1024-QAM on both 2.4 GHz & 5 GHz bands 
• Packet aggregation 

• Power over Ethernet: 42.5 – 57 V (802.3at) or 37 – 57 V (802.3af) – low power mode **
• Alternative: 12 V DC input 
• Power consumption: 30W max (802.3at) or 15W max (802.3af) – low power mode **
• Power over Ethernet injector and DC adapter sold separately

Note: Actual power consumption may vary depending on the AP usage.

In low power mode, MR44 will do the following:

1. Downshift its Ethernet uplink speed from 2.5 Gbps to 1 Gbps
2. Transition from 4×4:4 to 2×2:2 in 5GHz
3. Disable its dedicated IoT (previously known as BLE) radio
4. Disable its dedicated Scanning Radio
5. Reduce the max Tx power

Warning: Please ensure that MR44 is connected to an 802.3at-capable (PoE+) switch/power injector during the initial installation OR ensure that the network the MR44 is added to is set to MR 27.6 or newer firmware.

This is because the default MR44 firmware image has support for the low-power mode, however, MR 27.5/27.5.1 or lower firmware does not have low power mode support. Using 802.3af switch/power injector with MR44 set to 27.5/27.5.1 or lower firmware might result in unexpected behaviors including but not limited to reboots or degraded performance. 

Due to the reasons stated above, please do not downgrade the network with MR44 APs to 27.5/27.5.1 or lower firmware if they are being powered on by 802.3af (PoE) switch/power injector.

• 1x 100/1000/2.5G BASE-T Ethernet (RJ45) 
• 1x DC power connector (5.5 mm x 2.5 mm, center positive) 

• All standard mounting hardware included 
• Desktop, ceiling, and wall mount capable 
• Ceiling tile rail (9/16, 15/16 or 1 1⁄2” flush or recessed rails), assorted cable junction boxes 
• Bubble level on the mounting cradle for accurate horizontal wall mounting

• Two security screw options (included) (13.5 mm long and 2.5 mm diameter and 5 mm head) 
• Kensington lock hard point 
• Concealed mount plate with anti-tamper cable bay

• Operating altitude: Up to 40,000 feet (12,192 meters)
• Operating temperature: 32 °F to 104 °F (0 °C to 40 °C) 
• Humidity: 5 to 95% non-condensing 

• Mean Time Between Failure (MTBF): 500,000 hours at +25°C operating temperature

• 12.05″ × 5.06″ × 1.74″ (30.6 cm × 12.84 cm × 4.43 cm), not including desk mount feet or mount plate
• Weight: 26.07 oz (739 g)

• Integrated Layer 7 firewall with mobile device policy management 
• Real-time WIDS/WIPS with alerting and automatic rogue AP containment with Air Marshal 
• Flexible guest access with device isolation 
• VLAN tagging (802.1q) and tunneling with IPsec VPN 
• PCI compliance reporting 
• WEP***, WPA, WPA2-PSK, WPA2-Enterprise with 802.1X, WPA3 – Personal**, WPA3 – Enterprise**, WPA3 – Enhanced Open (OWE)**
• EAP-TLS, EAP-TTLS, EAP-MSCHAPv2, EAP-SIM 
• TKIP and AES encryption 
• Enterprise Mobility Management (EMM) & Mobile Device Management (MDM) integration 
• Cisco ISE integration for Guest access and BYOD Posturing 

• Advanced Power Save (U-APSD) 
• WMM Access Categories with DSCP and 802.1p support 
• Layer 7 application traffic identification and shaping 

• PMK, OKC, & 802.11r for fast Layer 2 roaming 
• Distributed or centralized layer 3 roaming

• Embedded location analytics reporting and device tracking 
• Global L7 traffic analytics reporting per network, per device, & per application

• 1 power/booting/firmware upgrade status 

• RoHS
• For additional country-specific regulatory information, please contact Meraki sales

• Indoor access point
• Lifetime hardware warranty with advanced replacement included

• MR44-HW: Meraki MR44 Cloud Managed 802.11ax AP 
• MA-PWR-30W-XX: Meraki AC Adapter for MR Series (XX = US/EU/UK/AU) 
• MA-INJ-4: Meraki MR 802.3at PoE Injector (Power Cord Not Included)
• MA-INJ-6: Meraki MR MultiGigabit 802.3bt Injector (Power Cord Not Included)
• Note: Meraki access point license required.